Boundary dimensions are 30 × 55 × 13 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 30 |
| Outside diameter D (mm) | 55 |
| Width B (mm) | 13 |
The base number splits into series 60 and bore code 06. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 06 therefore means a 30 mm bore, which matches the 30 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 13,200 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 13200 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 30 × 55 × 13 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | with snap-ring groove (U-groove) |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 30 × 55 × 13 mm; only sealing (and therefore drag and top speed) changes.
13,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 13000 |
36 listings share the 30 × 55 × 13 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6006LLBNR/2AS specifically: 3 exact equivalent, 14 close but not equivalent, 18 not interchangeable, 0 not assessable.
| Part number | vs 6006LLBNR/2AS | What differs | List price |
|---|---|---|---|
6006 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 854 |
6006CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 779 |
6006LB | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 913 |
6006LLB | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 916 |
6006LLB/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1200 |
6006LLBC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 1034 |
6006LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 928 |
6006LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 890 |
6006LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 798 |
6006LLBNR | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 757 |
6006LLU | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 832 |
6006LLU/2AS | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1050 |
6006LLU/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 996 |
6006LLUC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 904 |
6006LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 1034 |
6006LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 1064 |
6006LLUNR | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 1017 |
6006LLUNR/2AS | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 848 |
6006LU | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 669 |
6006NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 820 |
6006P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1800 |
6006Z | Not interchangeable | sealing: rubber seal vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 664 |
6006ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 601 |
6006ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 763 |
6006ZNR | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 847 |
6006ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 728 |
6006ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1130 |
6006ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 829 |
6006ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 956 |
6006ZZC4 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 846 |
6006ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 959 |
6006ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 585 |
6006ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 591 |
6006ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 917 |
6006ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 767 |
All 35 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 849 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.