6008LLBNR bearing (40 × 68 × 15 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6008LLBNR as a deep groove ball bearing with 40 mm bore × 68 mm outside diameter × 15 mm width · rubber seal · basic dynamic load rating C = 16,800 N · list price JPY 1,250/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6008LLBNR?

Boundary dimensions are 40 × 68 × 15 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)40
Outside diameter D (mm)68
Width B (mm)15
How is the part number 6008LLBNR read?

The base number splits into series 60 and bore code 08. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 08 therefore means a 40 mm bore, which matches the 40 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6008LLBNR?

C = 16,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)16800
Load directionradial
Rowssingle row
Is 6008LLBNR sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 40 × 68 × 15 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typewith snap-ring groove (U-groove)
Cagepressed steel
What does “LLB” mean in 6008LLBNR?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 40 × 68 × 15 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6008LLBNR?

10,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)10000
Which bearings can replace 6008LLBNR among the 40 × 68 × 15 mm parts?

31 listings share the 40 × 68 × 15 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6008LLBNR specifically: 3 exact equivalent, 13 close but not equivalent, 14 not interchangeable, 0 not assessable.

Part numbervs 6008LLBNRWhat differsList price
6008Not interchangeablesealing: rubber seal vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 953
6008CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1014
6008LBClose, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1155
6008LLBClose, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1315
6008LLBC3Close, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 1346
6008LLBC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 2098
6008LLBCMClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 1033
6008LLBCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 1157
6008LLBNR/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1260
6008LLUClose, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1286
6008LLU/LP03Close, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1580
6008LLUC3Close, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 1303
6008LLUC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 1234
6008LLUCMClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 1157
6008LLUCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 1299
6008LLUNRExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1516
6008LLUNR/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1332
6008LUClose, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1177
6008NRNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1021
6008P4Not interchangeablesealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 4; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 5403
6008ZNot interchangeablesealing: rubber seal vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1068
6008ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1260
6008ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1462
6008ZZNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1068
6008ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1460
6008ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1243
6008ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1045
6008ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1260
6008ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1086
6008ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1068

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6008LLBNR cost?

JPY 1,250 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6008LLBNR?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6008LLBNR. The listing is tools.agentkit.ltd/s/BT-6008LLBNR. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,250 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.