6009NR bearing (45 × 75 × 16 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6009NR as a deep groove ball bearing with 45 mm bore × 75 mm outside diameter × 16 mm width · open (no seal or shield) · basic dynamic load rating C = 21,000 N · list price JPY 1,500/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6009NR?

Boundary dimensions are 45 × 75 × 16 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)45
Outside diameter D (mm)75
Width B (mm)16
How is the part number 6009NR read?

The base number splits into series 60 and bore code 09. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 09 therefore means a 45 mm bore, which matches the 45 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6009NR?

C = 21,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)21000
Load directionradial
Rowssingle row
Is 6009NR sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 45 × 75 × 16 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typewith snap-ring groove (U-groove)
Cagepressed steel
What is the maximum speed of 6009NR?

9,200 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)9200
Which bearings can replace 6009NR among the 45 × 75 × 16 mm parts?

33 listings share the 45 × 75 × 16 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6009NR specifically: 0 exact equivalent, 3 close but not equivalent, 29 not interchangeable, 0 not assessable.

Part numbervs 6009NRWhat differsList price
6009Close, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1418
6009C3Close, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 1238
6009CMClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 1167
6009LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1519
6009LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1398
6009LLB/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1880
6009LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1595
6009LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1606
6009LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1251
6009LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1498
6009LLBP5/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 5050
6009LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1697
6009LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1776
6009LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1531
6009LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1251
6009LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1417
6009LLUNRNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1972
6009LLUNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1636
6009LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1580
6009P5Not interchangeableprecision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 3701
6009ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1513
6009ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1254
6009ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2395
6009ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1361
6009ZZ/LP03Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1730
6009ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1531
6009ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1420
6009ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1460
6009ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1269
6009ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1368
6009ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1838
6009ZZNR/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1474

All 32 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6009NR cost?

JPY 1,500 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6009NR?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6009NR. The listing is tools.agentkit.ltd/s/BT-6009NR. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,500 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.