Boundary dimensions are 55 × 90 × 18 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 55 |
| Outside diameter D (mm) | 90 |
| Width B (mm) | 18 |
The base number splits into series 60 and bore code 11. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 11 therefore means a 55 mm bore, which matches the 55 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 28,300 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 28300 |
| Load direction | radial |
| Rows | single row |
open (no seal or shield). Sealing is part of the part number: two bearings with the same 55 × 90 × 18 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | open (no seal or shield) |
| Outer ring type | flat |
| Cage | pressed steel |
7,700 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 7700 |
22 listings share the 55 × 90 × 18 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6011 specifically: 0 exact equivalent, 4 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6011 | What differs | List price |
|---|---|---|---|
6011C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 1710 |
6011CM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2587 |
6011L1C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2290 |
6011LLB | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2657 |
6011LLBCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1914 |
6011LLBCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2093 |
6011LLU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2657 |
6011LLUCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1767 |
6011LLUCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2094 |
6011LLUNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2280 |
6011NR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 1940 |
6011Z | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2104 |
6011ZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2507 |
6011ZZ | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2436 |
6011ZZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1836 |
6011ZZC3/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1880 |
6011ZZC4/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1880 |
6011ZZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1853 |
6011ZZCM/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1787 |
6011ZZNR | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2598 |
6011ZZNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2834 |
All 21 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,001 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.