Boundary dimensions are 60 × 95 × 18 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 60 |
| Outside diameter D (mm) | 95 |
| Width B (mm) | 18 |
The base number splits into series 60 and bore code 12. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 12 therefore means a 60 mm bore, which matches the 60 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 29,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 29500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 60 × 95 × 18 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 60 × 95 × 18 mm; only sealing (and therefore drag and top speed) changes.
4,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 4100 |
29 listings share the 60 × 95 × 18 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6012LLUCM specifically: 3 exact equivalent, 8 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6012LLUCM | What differs | List price |
|---|---|---|---|
6012 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2235 |
6012C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1817 |
6012C4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1860 |
6012CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1817 |
6012LB | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 2359 |
6012LLB | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 3068 |
6012LLBCM | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1912 |
6012LLBCM/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 2534 |
6012LLBNR | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 2879 |
6012LLBNR/2AS | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 2723 |
6012LLU | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 2531 |
6012LLUCM/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 2491 |
6012LLUNR | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 3599 |
6012LLUNR/2AS | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 2626 |
6012LU | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 2250 |
6012NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2120 |
6012P4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the other | JPY 8730 |
6012P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 7402 |
6012Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2600 |
6012ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2050 |
6012ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2616 |
6012ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2346 |
6012ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2307 |
6012ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3187 |
6012ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1828 |
6012ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2511 |
6012ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2403 |
6012ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2401 |
All 28 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,366 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.