Boundary dimensions are 65 × 100 × 18 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 65 |
| Outside diameter D (mm) | 100 |
| Width B (mm) | 18 |
The base number splits into series 60 and bore code 13. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 13 therefore means a 65 mm bore, which matches the 65 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 30,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 30500 |
| Load direction | radial |
| Rows | single row |
shielded, one side. Sealing is part of the part number: two bearings with the same 65 × 100 × 18 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, one side |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 65 × 100 × 18 mm; only sealing (and therefore drag and top speed) changes.
7,700 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 7700 |
20 listings share the 65 × 100 × 18 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6013ZCM specifically: 0 exact equivalent, 2 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6013ZCM | What differs | List price |
|---|---|---|---|
6013 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3139 |
6013CM | Not interchangeable | sealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2308 |
6013LB | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2570 |
6013LLB | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3078 |
6013LLBCM | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2417 |
6013LLBCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2567 |
6013LLU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3213 |
6013LLUC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2590 |
6013LLUCM | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2737 |
6013LLUCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2779 |
6013LU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2590 |
6013NR | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2624 |
6013P5 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 9708 |
6013Z | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 3045 |
6013ZC3 | Close, not equivalent | clearance: CM vs C3 | JPY 2512 |
6013ZZ | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2933 |
6013ZZC3/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2360 |
6013ZZCM | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2610 |
6013ZZCM/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2586 |
All 19 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 3,049 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.