Boundary dimensions are 70 × 110 × 20 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 70 |
| Outside diameter D (mm) | 110 |
| Width B (mm) | 20 |
The base number splits into series 60 and bore code 14. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 14 therefore means a 70 mm bore, which matches the 70 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 38,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 38000 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 70 × 110 × 20 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 70 × 110 × 20 mm; only sealing (and therefore drag and top speed) changes.
6,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 6100 |
23 listings share the 70 × 110 × 20 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6014ZZC3/5K specifically: 0 exact equivalent, 5 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6014ZZC3/5K | What differs | List price |
|---|---|---|---|
6014 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2791 |
6014C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2360 |
6014CM | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2641 |
6014L1 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3765 |
6014LB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3263 |
6014LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4058 |
6014LLBC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4054 |
6014LLBCM | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2761 |
6014LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3445 |
6014LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3017 |
6014LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4570 |
6014LU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3449 |
6014P5 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 8180 |
6014Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3414 |
6014ZC3 | Not interchangeable | sealing: shielded, both sides vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2620 |
6014ZCM | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3797 |
6014ZZ | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 2806 |
6014ZZC4/2AS | Close, not equivalent | clearance: C3 vs C4 | JPY 2443 |
6014ZZCM | Close, not equivalent | clearance: C3 vs CM | JPY 3047 |
6014ZZCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 2998 |
6014ZZNR/2AS | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 4650 |
6014ZZP5/2AS | Not interchangeable | clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 7798 |
All 22 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,620 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.