6016LU bearing (80 × 125 × 22 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6016LU as a deep groove ball bearing with 80 mm bore × 125 mm outside diameter × 22 mm width · rubber seal · basic dynamic load rating C = 47,500 N · list price JPY 5,470/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6016LU?

Boundary dimensions are 80 × 125 × 22 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)80
Outside diameter D (mm)125
Width B (mm)22
How is the part number 6016LU read?

The base number splits into series 60 and bore code 16. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 16 therefore means a 80 mm bore, which matches the 80 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6016LU?

C = 47,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)47500
Load directionradial
Rowssingle row
Is 6016LU sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 80 × 125 × 22 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LU” mean in 6016LU?

In this catalogue the suffix LU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 80 × 125 × 22 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6016LU?

3,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)3100
Which bearings can replace 6016LU among the 80 × 125 × 22 mm parts?

18 listings share the 80 × 125 × 22 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6016LU specifically: 4 exact equivalent, 2 close but not equivalent, 11 not interchangeable, 0 not assessable.

Part numbervs 6016LUWhat differsList price
6016Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4324
6016C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4720
6016C4Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4720
6016CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3778
6016L1C3P6Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the otherJPY 7700
6016LLBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 4780
6016LLB/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 4776
6016LLUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 4360
6016LLU/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 4521
6016LLUC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 4672
6016LLUC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 5630
6016ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4272
6016ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5090
6016ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4081
6016ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4971
6016ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4002
6016ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3854

All 17 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6016LU cost?

JPY 5,470 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6016LU?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6016LU. The listing is tools.agentkit.ltd/s/BT-6016LU. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 5,470 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.