6019CM bearing (95 × 145 × 24 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6019CM as a deep groove ball bearing with 95 mm bore × 145 mm outside diameter × 24 mm width · open (no seal or shield) · basic dynamic load rating C = 60,500 N · list price JPY 4,927/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6019CM?

Boundary dimensions are 95 × 145 × 24 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)95
Outside diameter D (mm)145
Width B (mm)24
How is the part number 6019CM read?

The base number splits into series 60 and bore code 19. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 19 therefore means a 95 mm bore, which matches the 95 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6019CM?

C = 60,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)60500
Load directionradial
Rowssingle row
Is 6019CM sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 95 × 145 × 24 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6019CM?

4,500 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)4500
Which bearings can replace 6019CM among the 95 × 145 × 24 mm parts?

10 listings share the 95 × 145 × 24 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6019CM specifically: 0 exact equivalent, 2 close but not equivalent, 7 not interchangeable, 0 not assessable.

Part numbervs 6019CMWhat differsList price
6019Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 5156
6019C4Close, not equivalentclearance: CM vs C4JPY 5698
6019LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6849
6019LLB/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7140
6019LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6952
6019ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6562
6019ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6058
6019ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5322
6019ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6028

All 9 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6019CM cost?

JPY 4,927 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6019CM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6019CM. The listing is tools.agentkit.ltd/s/BT-6019CM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 4,927 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.