6020LLU/2AS bearing (100 × 150 × 24 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6020LLU/2AS as a deep groove ball bearing with 100 mm bore × 150 mm outside diameter × 24 mm width · rubber seal · basic dynamic load rating C = 60,000 N · list price JPY 8,252/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6020LLU/2AS?

Boundary dimensions are 100 × 150 × 24 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)100
Outside diameter D (mm)150
Width B (mm)24
How is the part number 6020LLU/2AS read?

The base number splits into series 60 and bore code 20. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 20 therefore means a 100 mm bore, which matches the 100 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6020LLU/2AS?

C = 60,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)60000
Load directionradial
Rowssingle row
Is 6020LLU/2AS sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 100 × 150 × 24 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6020LLU/2AS?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 100 × 150 × 24 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6020LLU/2AS?

2,600 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)2600
Which bearings can replace 6020LLU/2AS among the 100 × 150 × 24 mm parts?

14 listings share the 100 × 150 × 24 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6020LLU/2AS specifically: 2 exact equivalent, 0 close but not equivalent, 11 not interchangeable, 0 not assessable.

Part numbervs 6020LLU/2ASWhat differsList price
6020Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6987
6020C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5723
6020C4Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6900
6020CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6517
6020LLUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 8183
6020LUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 7980
6020ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7742
6020ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7215
6020ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6987
6020ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 8944
6020ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 9181
6020ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6620
6020ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7475

All 13 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6020LLU/2AS cost?

JPY 8,252 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6020LLU/2AS?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6020LLU/2AS. The listing is tools.agentkit.ltd/s/BT-6020LLU-2AS. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 8,252 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.