6026 bearing (130 × 200 × 33 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6026 as a deep groove ball bearing with 130 mm bore × 200 mm outside diameter × 33 mm width · open (no seal or shield) · basic dynamic load rating C = 106,000 N · list price JPY 16,038/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6026?

Boundary dimensions are 130 × 200 × 33 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)130
Outside diameter D (mm)200
Width B (mm)33
How is the part number 6026 read?

The base number splits into series 60 and bore code 26. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 26 therefore means a 130 mm bore, which matches the 130 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6026?

C = 106,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)106000
Load directionradial
Rowssingle row
Is 6026 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 130 × 200 × 33 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
Which bearings can replace 6026 among the 130 × 200 × 33 mm parts?

7 listings share the 130 × 200 × 33 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6026 specifically: 0 exact equivalent, 2 close but not equivalent, 4 not interchangeable, 0 not assessable.

Part numbervs 6026What differsList price
6026C3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 14170
6026CMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 14170
6026LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 17914
6026LLU/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 21222
6026ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 15942
6026ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 22162

All 6 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6026 cost?

JPY 16,038 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6026?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6026. The listing is tools.agentkit.ltd/s/BT-6026. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 16,038 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.