6030Z bearing (150 × 225 × 35 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6030Z as a deep groove ball bearing with 150 mm bore × 225 mm outside diameter × 35 mm width · shielded, one side · basic dynamic load rating C = 126,000 N · list price JPY 22,890/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6030Z?

Boundary dimensions are 150 × 225 × 35 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)150
Outside diameter D (mm)225
Width B (mm)35
How is the part number 6030Z read?

The base number splits into series 60 and bore code 30. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 30 therefore means a 150 mm bore, which matches the 150 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6030Z?

C = 126,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)126000
Load directionradial
Rowssingle row
Is 6030Z sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 150 × 225 × 35 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6030Z?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 150 × 225 × 35 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6030Z?

3,200 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)3200
Which bearings can replace 6030Z among the 150 × 225 × 35 mm parts?

5 listings share the 150 × 225 × 35 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6030Z specifically: 0 exact equivalent, 0 close but not equivalent, 4 not interchangeable, 0 not assessable.

Part numbervs 6030ZWhat differsList price
6030C4Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 22211
6030CMNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 22275
6030LLU/2ASNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 28505
6030ZZNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 36709

All 4 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6030Z cost?

JPY 22,890 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6030Z?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6030Z. The listing is tools.agentkit.ltd/s/BT-6030Z. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 22,890 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.