Boundary dimensions are 30 × 62 × 16 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 30 |
| Outside diameter D (mm) | 62 |
| Width B (mm) | 16 |
The base number splits into series 62 and bore code 06. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 06 therefore means a 30 mm bore, which matches the 30 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 19,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 19500 |
| Load direction | radial |
| Rows | single row |
open (no seal or shield). Sealing is part of the part number: two bearings with the same 30 × 62 × 16 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | open (no seal or shield) |
| Outer ring type | flat |
| Cage | pressed steel |
11,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 11000 |
42 listings share the 30 × 62 × 16 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6206 specifically: 0 exact equivalent, 5 close but not equivalent, 36 not interchangeable, 0 not assessable.
| Part number | vs 6206 | What differs | List price |
|---|---|---|---|
6206C2 | Close, not equivalent | clearance: not stated (standard group assumed) vs C2 | JPY 777 |
6206C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 892 |
6206C4 | Close, not equivalent | clearance: not stated (standard group assumed) vs C4 | JPY 1010 |
6206CM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 730 |
6206L1C3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1240 |
6206LB | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 918 |
6206LLB | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1112 |
6206LLB/LP03 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1320 |
6206LLBC3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 947 |
6206LLBC3/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1329 |
6206LLBCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1034 |
6206LLBCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 852 |
6206LLBNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1230 |
6206LLBP5 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2666 |
6206LLBP5/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2465 |
6206LLU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 959 |
6206LLU/LP03 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1320 |
6206LLUC3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1154 |
6206LLUC3/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 962 |
6206LLUC4/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1140 |
6206LLUCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 859 |
6206LLUCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 933 |
6206LLUNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1230 |
6206LU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1222 |
6206NR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 973 |
6206Z | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 822 |
6206ZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 841 |
6206ZC4 | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 918 |
6206ZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 783 |
6206ZNR | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1170 |
6206ZZ | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 802 |
6206ZZ/LP03 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1220 |
6206ZZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 979 |
6206ZZC3/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 869 |
6206ZZC3/L448 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1080 |
6206ZZC4/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1080 |
6206ZZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1157 |
6206ZZCM/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 867 |
6206ZZNR | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1371 |
6206ZZNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1144 |
6206ZZP5/2AS | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2100 |
All 41 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 882 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.