6208ZCM bearing (40 × 80 × 18 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6208ZCM as a deep groove ball bearing with 40 mm bore × 80 mm outside diameter × 18 mm width · shielded, one side · basic dynamic load rating C = 29,100 N · list price JPY 1,280/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6208ZCM?

Boundary dimensions are 40 × 80 × 18 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)40
Outside diameter D (mm)80
Width B (mm)18
How is the part number 6208ZCM read?

The base number splits into series 62 and bore code 08. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 08 therefore means a 40 mm bore, which matches the 40 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6208ZCM?

C = 29,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)29100
Load directionradial
Rowssingle row
Is 6208ZCM sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 40 × 80 × 18 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6208ZCM?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 40 × 80 × 18 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6208ZCM?

10,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)10000
Which bearings can replace 6208ZCM among the 40 × 80 × 18 mm parts?

37 listings share the 40 × 80 × 18 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6208ZCM specifically: 0 exact equivalent, 3 close but not equivalent, 33 not interchangeable, 0 not assessable.

Part numbervs 6208ZCMWhat differsList price
6208Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1239
6208C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1178
6208C3P5Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 4740
6208C4Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1320
6208CMNot interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1197
6208L1C3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1710
6208LBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1768
6208LLBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1901
6208LLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1768
6208LLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2729
6208LLBCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1514
6208LLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1721
6208LLBNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1690
6208LLBP5/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 4945
6208LLUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6208LLU/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2140
6208LLUC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1825
6208LLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1429
6208LLUCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1394
6208LLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1422
6208LLUNRNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2108
6208LLUNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1594
6208LUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1899
6208M8C3P6Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1920
6208NRNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1484
6208ZClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1392
6208ZC3Close, not equivalentclearance: CM vs C3JPY 1440
6208ZC4Close, not equivalentclearance: CM vs C4JPY 1440
6208ZZNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1313
6208ZZ/LP03Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1970
6208ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1529
6208ZZC3/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1291
6208ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1322
6208ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1475
6208ZZNRNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1821
6208ZZNR/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1436

All 36 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6208ZCM cost?

JPY 1,280 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6208ZCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6208ZCM. The listing is tools.agentkit.ltd/s/BT-6208ZCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,280 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.