6209LLB bearing (45 × 85 × 19 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6209LLB as a deep groove ball bearing with 45 mm bore × 85 mm outside diameter × 19 mm width · rubber seal · basic dynamic load rating C = 32,500 N · list price JPY 1,864/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6209LLB?

Boundary dimensions are 45 × 85 × 19 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)45
Outside diameter D (mm)85
Width B (mm)19
How is the part number 6209LLB read?

The base number splits into series 62 and bore code 09. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 09 therefore means a 45 mm bore, which matches the 45 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6209LLB?

C = 32,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)32500
Load directionradial
Rowssingle row
Is 6209LLB sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 45 × 85 × 19 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6209LLB?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 45 × 85 × 19 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6209LLB?

7,800 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)7800
Which bearings can replace 6209LLB among the 45 × 85 × 19 mm parts?

31 listings share the 45 × 85 × 19 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6209LLB specifically: 3 exact equivalent, 9 close but not equivalent, 18 not interchangeable, 0 not assessable.

Part numbervs 6209LLBWhat differsList price
6209Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1476
6209C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1662
6209C4Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1500
6209CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1496
6209LBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 2122
6209LLBC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 1975
6209LLBC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 1913
6209LLBCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 1554
6209LLBCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 1848
6209LLUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1923
6209LLUC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 1964
6209LLUC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 1863
6209LLUCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 1835
6209LLUCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 1793
6209LLUNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 1960
6209LUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1770
6209NRNot interchangeablesealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1554
6209ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1785
6209ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1640
6209ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1600
6209ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1621
6209ZZ/2ASNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1640
6209ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1699
6209ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1801
6209ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1640
6209ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1662
6209ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6209ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2473
6209ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1663
6209ZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 5460

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6209LLB cost?

JPY 1,864 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6209LLB?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6209LLB. The listing is tools.agentkit.ltd/s/BT-6209LLB. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,864 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.