Boundary dimensions are 65 × 120 × 23 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 65 |
| Outside diameter D (mm) | 120 |
| Width B (mm) | 23 |
The base number splits into series 62 and bore code 13. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 13 therefore means a 65 mm bore, which matches the 65 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 57,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 57500 |
| Load direction | radial |
| Rows | single row |
open (no seal or shield). Sealing is part of the part number: two bearings with the same 65 × 120 × 23 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | open (no seal or shield) |
| Outer ring type | flat |
| Cage | pressed steel |
21 listings share the 65 × 120 × 23 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6213 specifically: 0 exact equivalent, 4 close but not equivalent, 16 not interchangeable, 0 not assessable.
| Part number | vs 6213 | What differs | List price |
|---|---|---|---|
6213C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2885 |
6213C4 | Close, not equivalent | clearance: not stated (standard group assumed) vs C4 | JPY 2380 |
6213CM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2921 |
6213L1C3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4970 |
6213LLB | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3825 |
6213LLBC3/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4610 |
6213LLBCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3315 |
6213LLU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3823 |
6213LLUC3/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4610 |
6213LLUCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2813 |
6213LLUCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3503 |
6213LU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3315 |
6213NR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 4430 |
6213Z | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3237 |
6213ZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2650 |
6213ZZ | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3005 |
6213ZZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3522 |
6213ZZC3/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3102 |
6213ZZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2481 |
6213ZZNR | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3338 |
All 20 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 3,287 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.