Boundary dimensions are 70 × 125 × 24 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 70 |
| Outside diameter D (mm) | 125 |
| Width B (mm) | 24 |
The base number splits into series 62 and bore code 14. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 14 therefore means a 70 mm bore, which matches the 70 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 62,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 62000 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 70 × 125 × 24 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 70 × 125 × 24 mm; only sealing (and therefore drag and top speed) changes.
5,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 5100 |
20 listings share the 70 × 125 × 24 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6214ZZCM specifically: 1 exact equivalent, 4 close but not equivalent, 14 not interchangeable, 0 not assessable.
| Part number | vs 6214ZZCM | What differs | List price |
|---|---|---|---|
6214 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3523 |
6214C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3100 |
6214CM | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2821 |
6214L1 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5310 |
6214LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3826 |
6214LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4799 |
6214LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4213 |
6214LLUC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3319 |
6214LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3978 |
6214LLUCM | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3007 |
6214LLUCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3927 |
6214Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3115 |
6214ZC3 | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4590 |
6214ZCM | Not interchangeable | sealing: shielded, both sides vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2835 |
6214ZZ | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 3704 |
6214ZZC3 | Close, not equivalent | clearance: CM vs C3 | JPY 3196 |
6214ZZC3/5K | Close, not equivalent | clearance: CM vs C3 | JPY 3289 |
6214ZZCM/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 3289 |
6214ZZNR/2AS | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 4990 |
All 19 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 3,461 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.