Boundary dimensions are 75 × 130 × 25 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 75 |
| Outside diameter D (mm) | 130 |
| Width B (mm) | 25 |
The base number splits into series 62 and bore code 15. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 15 therefore means a 75 mm bore, which matches the 75 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 66,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 66000 |
| Load direction | radial |
| Rows | single row |
shielded, one side. Sealing is part of the part number: two bearings with the same 75 × 130 × 25 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, one side |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 75 × 130 × 25 mm; only sealing (and therefore drag and top speed) changes.
5,600 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 5600 |
21 listings share the 75 × 130 × 25 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6215ZC3 specifically: 0 exact equivalent, 2 close but not equivalent, 18 not interchangeable, 0 not assessable.
| Part number | vs 6215ZC3 | What differs | List price |
|---|---|---|---|
6215 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3590 |
6215C3 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3349 |
6215CM | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3156 |
6215L1C3 | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5330 |
6215LLB | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5256 |
6215LLBCM | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3321 |
6215LLBCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4105 |
6215LLU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3713 |
6215LLUC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4105 |
6215LLUCM | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3497 |
6215LLUCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3895 |
6215LU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5180 |
6215Z | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 3195 |
6215ZCM | Close, not equivalent | clearance: C3 vs CM | JPY 3957 |
6215ZZ | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3956 |
6215ZZC3 | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3645 |
6215ZZC3/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3334 |
6215ZZCM | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3235 |
6215ZZCM/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3631 |
6215ZZNR/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5280 |
All 20 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 4,830 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.