Boundary dimensions are 90 × 160 × 30 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 90 |
| Outside diameter D (mm) | 160 |
| Width B (mm) | 30 |
The base number splits into series 62 and bore code 18. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 18 therefore means a 90 mm bore, which matches the 90 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 96,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 96000 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 90 × 160 × 30 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 90 × 160 × 30 mm; only sealing (and therefore drag and top speed) changes.
4,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 4000 |
18 listings share the 90 × 160 × 30 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6218ZZCM specifically: 1 exact equivalent, 3 close but not equivalent, 13 not interchangeable, 0 not assessable.
| Part number | vs 6218ZZCM | What differs | List price |
|---|---|---|---|
6218 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6051 |
6218C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5698 |
6218C4 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5141 |
6218CM | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5422 |
6218LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7442 |
6218LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8697 |
6218LLBCM | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6323 |
6218LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7150 |
6218LLUCM | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5881 |
6218NR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7050 |
6218ZC3 | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6562 |
6218ZC4 | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6518 |
6218ZNR | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7750 |
6218ZZ | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 6784 |
6218ZZC3/5K | Close, not equivalent | clearance: CM vs C3 | JPY 6940 |
6218ZZCM/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 6562 |
6218ZZNR/2AS | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 7750 |
All 17 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 5,322 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.