6221CM bearing (105 × 190 × 36 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6221CM as a deep groove ball bearing with 105 mm bore × 190 mm outside diameter × 36 mm width · open (no seal or shield) · basic dynamic load rating C = 133,000 N · list price JPY 11,351/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6221CM?

Boundary dimensions are 105 × 190 × 36 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)105
Outside diameter D (mm)190
Width B (mm)36
How is the part number 6221CM read?

The base number splits into series 62 and bore code 21. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 21 therefore means a 105 mm bore, which matches the 105 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6221CM?

C = 133,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)133000
Load directionradial
Rowssingle row
Is 6221CM sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 105 × 190 × 36 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6221CM?

3,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)3400
Which bearings can replace 6221CM among the 105 × 190 × 36 mm parts?

8 listings share the 105 × 190 × 36 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6221CM specifically: 0 exact equivalent, 2 close but not equivalent, 5 not interchangeable, 0 not assessable.

Part numbervs 6221CMWhat differsList price
6221C3Close, not equivalentclearance: CM vs C3JPY 11351
6221LLU/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 12437
6221NRClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 11634
6221ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 11216
6221ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 11641
6221ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 10935
6221ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 11652

All 7 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6221CM cost?

JPY 11,351 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6221CM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6221CM. The listing is tools.agentkit.ltd/s/BT-6221CM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 11,351 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.