6222ZZCM bearing (110 × 200 × 38 mm) — shielded, both sides

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6222ZZCM as a deep groove ball bearing with 110 mm bore × 200 mm outside diameter × 38 mm width · shielded, both sides · basic dynamic load rating C = 144,000 N · list price JPY 15,314/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6222ZZCM?

Boundary dimensions are 110 × 200 × 38 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)110
Outside diameter D (mm)200
Width B (mm)38
How is the part number 6222ZZCM read?

The base number splits into series 62 and bore code 22. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 22 therefore means a 110 mm bore, which matches the 110 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6222ZZCM?

C = 144,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)144000
Load directionradial
Rowssingle row
Is 6222ZZCM sealed or open?

shielded, both sides. Sealing is part of the part number: two bearings with the same 110 × 200 × 38 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, both sides
Outer ring typeflat
Cagepressed steel
What does “ZZ” mean in 6222ZZCM?

In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 110 × 200 × 38 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6222ZZCM?

3,200 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)3200
Which bearings can replace 6222ZZCM among the 110 × 200 × 38 mm parts?

8 listings share the 110 × 200 × 38 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6222ZZCM specifically: 1 exact equivalent, 1 close but not equivalent, 5 not interchangeable, 0 not assessable.

Part numbervs 6222ZZCMWhat differsList price
6222C3Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 12379
6222CMNot interchangeablesealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 13415
6222LLU/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 17310
6222NRNot interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 14459
6222ZNot interchangeablesealing: shielded, both sides vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 14731
6222ZZ/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 15992
6222ZZCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 15293

All 7 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6222ZZCM cost?

JPY 15,314 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6222ZZCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6222ZZCM. The listing is tools.agentkit.ltd/s/BT-6222ZZCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 15,314 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.