6230LLU/2AS bearing (150 × 270 × 45 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6230LLU/2AS as a deep groove ball bearing with 150 mm bore × 270 mm outside diameter × 45 mm width · rubber seal · basic dynamic load rating C = 176,000 N · list price JPY 55,430/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6230LLU/2AS?

Boundary dimensions are 150 × 270 × 45 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)150
Outside diameter D (mm)270
Width B (mm)45
How is the part number 6230LLU/2AS read?

The base number splits into series 62 and bore code 30. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 30 therefore means a 150 mm bore, which matches the 150 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6230LLU/2AS?

C = 176,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)176000
Load directionradial
Rowssingle row
Is 6230LLU/2AS sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 150 × 270 × 45 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6230LLU/2AS?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 150 × 270 × 45 mm; only sealing (and therefore drag and top speed) changes.

Which bearings can replace 6230LLU/2AS among the 150 × 270 × 45 mm parts?

4 listings share the 150 × 270 × 45 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6230LLU/2AS specifically: 0 exact equivalent, 0 close but not equivalent, 3 not interchangeable, 0 not assessable.

Part numbervs 6230LLU/2ASWhat differsList price
6230C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 39402
6230CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 42329
6230ZZ/2ASNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 51824

All 3 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6230LLU/2AS cost?

JPY 55,430 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6230LLU/2AS?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6230LLU/2AS. The listing is tools.agentkit.ltd/s/BT-6230LLU-2AS. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 55,430 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.