6301LLBCM bearing (12 × 37 × 12 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6301LLBCM as a deep groove ball bearing with 12 mm bore × 37 mm outside diameter × 12 mm width · rubber seal · basic dynamic load rating C = 9,700 N · list price JPY 697/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6301LLBCM?

Boundary dimensions are 12 × 37 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)12
Outside diameter D (mm)37
Width B (mm)12
How is the part number 6301LLBCM read?

The base number splits into series 63 and bore code 01. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 01 therefore means a 12 mm bore, which matches the 12 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6301LLBCM?

C = 9,700 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)9700
Load directionradial
Rowssingle row
Is 6301LLBCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 12 × 37 × 12 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6301LLBCM?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 12 × 37 × 12 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6301LLBCM?

20,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)20000
Which bearings can replace 6301LLBCM among the 12 × 37 × 12 mm parts?

24 listings share the 12 × 37 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6301LLBCM specifically: 3 exact equivalent, 8 close but not equivalent, 12 not interchangeable, 0 not assessable.

Part numbervs 6301LLBCMWhat differsList price
6301Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 630
6301C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 585
6301CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 628
6301LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 801
6301LLBC3Close, not equivalentclearance: CM vs C3JPY 815
6301LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 741
6301LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 778
6301LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 778
6301LLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1030
6301LLUC3Close, not equivalentclearance: CM vs C3JPY 759
6301LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 692
6301LLUCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 756
6301LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 589
6301LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 910
6301ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 518
6301ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 583
6301ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 473
6301ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 714
6301ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 678
6301ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 644
6301ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 665
6301ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 803
6301ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 708

All 23 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6301LLBCM cost?

JPY 697 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6301LLBCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6301LLBCM. The listing is tools.agentkit.ltd/s/BT-6301LLBCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 697 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.