6304LLUCM bearing (20 × 52 × 15 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6304LLUCM as a deep groove ball bearing with 20 mm bore × 52 mm outside diameter × 15 mm width · rubber seal · basic dynamic load rating C = 15,900 N · list price JPY 979/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6304LLUCM?

Boundary dimensions are 20 × 52 × 15 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)20
Outside diameter D (mm)52
Width B (mm)15
How is the part number 6304LLUCM read?

The base number splits into series 63 and bore code 04. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 04 therefore means a 20 mm bore, which matches the 20 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6304LLUCM?

C = 15,900 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)15900
Load directionradial
Rowssingle row
Is 6304LLUCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 20 × 52 × 15 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6304LLUCM?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 20 × 52 × 15 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6304LLUCM?

10,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)10000
Which bearings can replace 6304LLUCM among the 20 × 52 × 15 mm parts?

31 listings share the 20 × 52 × 15 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6304LLUCM specifically: 3 exact equivalent, 12 close but not equivalent, 15 not interchangeable, 0 not assessable.

Part numbervs 6304LLUCMWhat differsList price
6304Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 584
6304C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 657
6304C4Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 763
6304CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 546
6304JR2LLHC3/L448QTClose, not equivalentclearance: CM vs C3JPY 1080
6304L1C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 743
6304LBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 894
6304LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 980
6304LLBC3Close, not equivalentclearance: CM vs C3JPY 964
6304LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 971
6304LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 897
6304LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 748
6304LLBNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 1140
6304LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 718
6304LLUC3Close, not equivalentclearance: CM vs C3JPY 894
6304LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 838
6304LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 790
6304LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 1140
6304LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1060
6304NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1020
6304ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 857
6304ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 940
6304ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 749
6304ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 766
6304ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 884
6304ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1000
6304ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 837
6304ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 896
6304ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 796
EC-6304LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 1270

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6304LLUCM cost?

JPY 979 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6304LLUCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6304LLUCM. The listing is tools.agentkit.ltd/s/BT-6304LLUCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 979 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.