Boundary dimensions are 45 × 100 × 25 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 45 |
| Outside diameter D (mm) | 100 |
| Width B (mm) | 25 |
The base number splits into series 63 and bore code 09. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 09 therefore means a 45 mm bore, which matches the 45 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 53,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 53000 |
| Load direction | radial |
| Rows | single row |
open (no seal or shield). Sealing is part of the part number: two bearings with the same 45 × 100 × 25 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | open (no seal or shield) |
| Outer ring type | flat |
| Cage | pressed steel |
7,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 7000 |
31 listings share the 45 × 100 × 25 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6309 specifically: 0 exact equivalent, 4 close but not equivalent, 26 not interchangeable, 0 not assessable.
| Part number | vs 6309 | What differs | List price |
|---|---|---|---|
6309C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2788 |
6309CM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2545 |
6309L1C3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 4620 |
6309LLB | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2798 |
6309LLBC3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3056 |
6309LLBCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2864 |
6309LLBCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2913 |
6309LLBNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4336 |
6309LLU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3088 |
6309LLUC3 | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3002 |
6309LLUC3/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2887 |
6309LLUCM | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2619 |
6309LLUCM/5K | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2784 |
6309LLUNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs rubber seal; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4620 |
6309LU | Not interchangeable | sealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2620 |
6309NR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 2732 |
6309Z | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2334 |
6309ZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2390 |
6309ZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3465 |
6309ZZ | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3208 |
6309ZZC3 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3385 |
6309ZZC3/2AS | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2390 |
6309ZZC3/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2661 |
6309ZZC4 | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3556 |
6309ZZC4/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3696 |
6309ZZCM | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2951 |
6309ZZCM/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2982 |
6309ZZD2C3/5K | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6620 |
6309ZZNR | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2698 |
6309ZZNR/2AS | Not interchangeable | sealing: open (no seal or shield) vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2892 |
All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,501 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.