Boundary dimensions are 55 × 120 × 29 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 55 |
| Outside diameter D (mm) | 120 |
| Width B (mm) | 29 |
The base number splits into series 63 and bore code 11. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 11 therefore means a 55 mm bore, which matches the 55 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 71,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 71500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 55 × 120 × 29 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 55 × 120 × 29 mm; only sealing (and therefore drag and top speed) changes.
3,900 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 3900 |
25 listings share the 55 × 120 × 29 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6311LLUC3 specifically: 3 exact equivalent, 5 close but not equivalent, 16 not interchangeable, 0 not assessable.
| Part number | vs 6311LLUC3 | What differs | List price |
|---|---|---|---|
6311 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3018 |
6311CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3218 |
6311L1C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5300 |
6311LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 4961 |
6311LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 4661 |
6311LLBC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 4275 |
6311LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 3259 |
6311LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 4225 |
6311LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 4289 |
6311LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 4068 |
6311LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 4068 |
6311M8C3P6 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the other | JPY 5960 |
6311NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4910 |
6311Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4044 |
6311ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4810 |
6311ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3598 |
6311ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4013 |
6311ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4722 |
6311ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3802 |
6311ZZC4 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3564 |
6311ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3780 |
6311ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4102 |
6311ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3862 |
6311ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5250 |
All 24 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 3,536 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.