Boundary dimensions are 75 × 160 × 37 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 75 |
| Outside diameter D (mm) | 160 |
| Width B (mm) | 37 |
The base number splits into series 63 and bore code 15. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 15 therefore means a 75 mm bore, which matches the 75 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 113,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 113000 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 75 × 160 × 37 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 75 × 160 × 37 mm; only sealing (and therefore drag and top speed) changes.
4,300 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 4300 |
17 listings share the 75 × 160 × 37 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6315ZZC3/5K specifically: 1 exact equivalent, 2 close but not equivalent, 13 not interchangeable, 0 not assessable.
| Part number | vs 6315ZZC3/5K | What differs | List price |
|---|---|---|---|
6315 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6672 |
6315C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7603 |
6315L1C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 9500 |
6315LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 9841 |
6315LLBC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8936 |
6315LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 9311 |
6315LLBCM | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8439 |
6315LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 9311 |
6315LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8272 |
6315LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8309 |
6315NR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7353 |
6315Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 8767 |
6315ZCM | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6960 |
6315ZZC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 8415 |
6315ZZC4/5K | Close, not equivalent | clearance: C3 vs C4 | JPY 7980 |
6315ZZCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 9116 |
All 16 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 7,616 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.