Boundary dimensions are 25 × 37 × 7 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 25 |
| Outside diameter D (mm) | 37 |
| Width B (mm) | 7 |
The base number splits into series 68 and bore code 05. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 05 therefore means a 25 mm bore, which matches the 25 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 4,300 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 4300 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 25 × 37 × 7 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | with snap-ring groove (U-groove) |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 25 × 37 × 7 mm; only sealing (and therefore drag and top speed) changes.
18,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 18000 |
26 listings share the 25 × 37 × 7 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6805ZZNR specifically: 2 exact equivalent, 9 close but not equivalent, 14 not interchangeable, 0 not assessable.
| Part number | vs 6805ZZNR | What differs | List price |
|---|---|---|---|
6805 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 806 |
6805JR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 820 |
6805JRLLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1115 |
6805JRLLB/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 988 |
6805JRLLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1031 |
6805JRLLU/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1034 |
6805JRNR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1180 |
6805JRZ | Not interchangeable | sealing: shielded, both sides vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 779 |
6805JRZZ | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1036 |
6805JRZZ/2AS | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 882 |
6805JRZZ/5K | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1040 |
6805JRZZ/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1098 |
6805JRZZC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 1160 |
6805JRZZNR | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 1244 |
6805LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1065 |
6805LLB/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1031 |
6805LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 971 |
6805LLU/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 888 |
6805NR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1002 |
6805Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 860 |
6805ZZ | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1008 |
6805ZZ/2AS | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 948 |
6805ZZ/5K | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1042 |
6805ZZ/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 1360 |
6805ZZNR/2AS | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 1070 |
All 25 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 987 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.