Boundary dimensions are 30 × 42 × 7 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 30 |
| Outside diameter D (mm) | 42 |
| Width B (mm) | 7 |
The base number splits into series 68 and bore code 06. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 06 therefore means a 30 mm bore, which matches the 30 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 4,700 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 4700 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 30 × 42 × 7 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 30 × 42 × 7 mm; only sealing (and therefore drag and top speed) changes.
15,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 15000 |
19 listings share the 30 × 42 × 7 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6806ZZ specifically: 3 exact equivalent, 8 close but not equivalent, 7 not interchangeable, 0 not assessable.
| Part number | vs 6806ZZ | What differs | List price |
|---|---|---|---|
6806 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1005 |
6806JR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1034 |
6806JRLLB | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1163 |
6806JRZ | Not interchangeable | sealing: shielded, both sides vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1154 |
6806JRZZ | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 1181 |
6806JRZZ/5K | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 926 |
6806JRZZC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 1310 |
6806JRZZCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 942 |
6806JRZZCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 1059 |
6806JRZZNR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 1300 |
6806JRZZNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 1222 |
6806LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1366 |
6806LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1351 |
6806LLU/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1044 |
6806ZZ/2AS | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 1056 |
6806ZZCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 1064 |
6806ZZNR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 1857 |
6806ZZNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 1250 |
All 18 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 1,228 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.