Boundary dimensions are 10 × 22 × 6 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 10 |
| Outside diameter D (mm) | 22 |
| Width B (mm) | 6 |
The base number splits into series 69 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 2,700 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 2700 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 10 × 22 × 6 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | with snap-ring groove (U-groove) |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 10 × 22 × 6 mm; only sealing (and therefore drag and top speed) changes.
30,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 30000 |
22 listings share the 10 × 22 × 6 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6900ZZNR specifically: 1 exact equivalent, 5 close but not equivalent, 15 not interchangeable, 0 not assessable.
| Part number | vs 6900ZZNR | What differs | List price |
|---|---|---|---|
6900 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 697 |
6900LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 569 |
6900LLB/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 631 |
6900LLBC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 788 |
6900LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 728 |
6900LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 728 |
6900LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 667 |
6900LLU/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 695 |
6900LLU/LP03 | Not interchangeable | sealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 840 |
6900LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 990 |
6900LLUNR | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 882 |
6900LLUNR/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 757 |
6900NR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 835 |
6900Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 646 |
6900ZZ | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 646 |
6900ZZ/5K | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 588 |
6900ZZ/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 790 |
6900ZZC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 549 |
6900ZZC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 618 |
6900ZZNR/2AS | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 810 |
6900ZZP5/2AS | Not interchangeable | precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1690 |
All 21 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 749 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.