6902LLU bearing (15 × 28 × 7 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6902LLU as a deep groove ball bearing with 15 mm bore × 28 mm outside diameter × 7 mm width · rubber seal · basic dynamic load rating C = 3,650 N · list price JPY 822/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6902LLU?

Boundary dimensions are 15 × 28 × 7 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)15
Outside diameter D (mm)28
Width B (mm)7
How is the part number 6902LLU read?

The base number splits into series 69 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6902LLU?

C = 3,650 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)3650
Load directionradial
Rowssingle row
Is 6902LLU sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 15 × 28 × 7 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6902LLU?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 15 × 28 × 7 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6902LLU?

16,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)16000
Which bearings can replace 6902LLU among the 15 × 28 × 7 mm parts?

17 listings share the 15 × 28 × 7 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6902LLU specifically: 4 exact equivalent, 1 close but not equivalent, 11 not interchangeable, 0 not assessable.

Part numbervs 6902LLUWhat differsList price
6902Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 735
6902LLBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 766
6902LLB/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 814
6902LLU/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 806
6902LLUNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 1120
6902LUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1050
6902NRNot interchangeablesealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1010
6902ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 701
6902ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 719
6902ZZ/2ASNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 659
6902ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 879
6902ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 704
6902ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 631
6902ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 682
6902ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 756
6902ZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1850

All 16 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6902LLU cost?

JPY 822 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6902LLU?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6902LLU. The listing is tools.agentkit.ltd/s/BT-6902LLU. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 822 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.