Boundary dimensions are 15 × 32 × 9 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 15 |
| Outside diameter D (mm) | 32 |
| Width B (mm) | 9 |
The base number splits into series 60 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 5,600 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 5600 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 15 × 32 × 9 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | with snap-ring groove (U-groove) |
| Cage | pressed steel |
In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 15 × 32 × 9 mm; only sealing (and therefore drag and top speed) changes.
15,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 15000 |
39 listings share the 15 × 32 × 9 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6002LLUNR specifically: 1 exact equivalent, 15 close but not equivalent, 22 not interchangeable, 0 not assessable.
| Part number | vs 6002LLUNR | What differs | List price |
|---|---|---|---|
6002 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 537 |
6002C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 586 |
6002CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 535 |
6002LB | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 890 |
6002LLB | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 501 |
6002LLB/5K | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 701 |
6002LLB/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 980 |
6002LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 768 |
6002LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 687 |
6002LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 472 |
6002LLBNR/2AS | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 940 |
6002LLBP5 | Not interchangeable | precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1111 |
6002LLBP5/2AS | Not interchangeable | precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1319 |
6002LLU | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 527 |
6002LLU/LP03 | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 980 |
6002LLUC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 823 |
6002LLUC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 762 |
6002LLUC4 | Close, not equivalent | clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat | JPY 657 |
6002LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 734 |
6002LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 535 |
6002LU | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 550 |
6002NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 860 |
6002P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1344 |
6002U1 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 416 |
6002Z | Not interchangeable | sealing: rubber seal vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 494 |
6002ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 475 |
6002ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 604 |
6002ZNR | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 900 |
6002ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 494 |
6002ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 940 |
6002ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 544 |
6002ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 695 |
6002ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 850 |
6002ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 441 |
6002ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 492 |
6002ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 851 |
6002ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 558 |
6002ZZNRC3/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 900 |
All 38 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 686 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.