6002P5 bearing (15 × 32 × 9 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6002P5 as a deep groove ball bearing with 15 mm bore × 32 mm outside diameter × 9 mm width · open (no seal or shield) · basic dynamic load rating C = 5,600 N · list price JPY 1,344/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6002P5?

Boundary dimensions are 15 × 32 × 9 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)15
Outside diameter D (mm)32
Width B (mm)9
How is the part number 6002P5 read?

The base number splits into series 60 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6002P5?

C = 5,600 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5600
Load directionradial
Rowssingle row
Is 6002P5 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 15 × 32 × 9 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6002P5?

22,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)22000
Which bearings can replace 6002P5 among the 15 × 32 × 9 mm parts?

39 listings share the 15 × 32 × 9 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6002P5 specifically: 0 exact equivalent, 0 close but not equivalent, 38 not interchangeable, 0 not assessable.

Part numbervs 6002P5What differsList price
6002Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 537
6002C3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 586
6002CMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 535
6002LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 890
6002LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 501
6002LLB/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 701
6002LLB/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 980
6002LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 768
6002LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 687
6002LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 472
6002LLBNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6002LLBP5Not interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1111
6002LLBP5/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1319
6002LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 527
6002LLU/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 980
6002LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 823
6002LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 762
6002LLUC4Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 657
6002LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 734
6002LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 535
6002LLUNRNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 686
6002LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 550
6002NRNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 860
6002U1Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 416
6002ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 494
6002ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 475
6002ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 604
6002ZNRNot interchangeablesealing: open (no seal or shield) vs shielded, one side; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 900
6002ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 494
6002ZZ/LP03Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6002ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 544
6002ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 695
6002ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 850
6002ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 441
6002ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 492
6002ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 851
6002ZZNR/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 558
6002ZZNRC3/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 900

All 38 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6002P5 cost?

JPY 1,344 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6002P5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6002P5. The listing is tools.agentkit.ltd/s/BT-6002P5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,344 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.