6004ZC3 bearing (20 × 42 × 12 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6004ZC3 as a deep groove ball bearing with 20 mm bore × 42 mm outside diameter × 12 mm width · shielded, one side · basic dynamic load rating C = 7,900 N · list price JPY 532/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6004ZC3?

Boundary dimensions are 20 × 42 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)20
Outside diameter D (mm)42
Width B (mm)12
How is the part number 6004ZC3 read?

The base number splits into series 60 and bore code 04. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 04 therefore means a 20 mm bore, which matches the 20 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6004ZC3?

C = 7,900 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)7900
Load directionradial
Rowssingle row
Is 6004ZC3 sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 20 × 42 × 12 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6004ZC3?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 20 × 42 × 12 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6004ZC3?

21,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)21000
Which bearings can replace 6004ZC3 among the 20 × 42 × 12 mm parts?

37 listings share the 20 × 42 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6004ZC3 specifically: 0 exact equivalent, 3 close but not equivalent, 33 not interchangeable, 0 not assessable.

Part numbervs 6004ZC3What differsList price
6004Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 624
6004C3Not interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 648
6004CMNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 450
6004LBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 764
6004LLBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 604
6004LLB/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 768
6004LLBC3Not interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 792
6004LLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 876
6004LLBCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 701
6004LLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 603
6004LLBNRNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 716
6004LLBNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 715
6004LLUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 665
6004LLUC3Not interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 631
6004LLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 835
6004LLUCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 784
6004LLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 550
6004LLUNRNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 688
6004LLUNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 672
6004LUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 581
6004NRNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 817
6004P4Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1910
6004P5Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1296
6004ZClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 533
6004ZCMClose, not equivalentclearance: C3 vs CMJPY 409
6004ZNRClose, not equivalentclearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 930
6004ZZNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 487
6004ZZ/LP03Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 608
6004ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 767
6004ZZC3/5KNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 821
6004ZZC4/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 870
6004ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 424
6004ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 534
6004ZZNRNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 581
6004ZZNR/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 586
6004ZZP5/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1500

All 36 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6004ZC3 cost?

JPY 532 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6004ZC3?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6004ZC3. The listing is tools.agentkit.ltd/s/BT-6004ZC3. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 532 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.