Boundary dimensions are 20 × 42 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 20 |
| Outside diameter D (mm) | 42 |
| Width B (mm) | 12 |
The base number splits into series 60 and bore code 04. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 04 therefore means a 20 mm bore, which matches the 20 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 7,900 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 7900 |
| Load direction | radial |
| Rows | single row |
shielded, one side. Sealing is part of the part number: two bearings with the same 20 × 42 × 12 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, one side |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 20 × 42 × 12 mm; only sealing (and therefore drag and top speed) changes.
21,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 21000 |
37 listings share the 20 × 42 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6004ZCM specifically: 0 exact equivalent, 3 close but not equivalent, 33 not interchangeable, 0 not assessable.
| Part number | vs 6004ZCM | What differs | List price |
|---|---|---|---|
6004 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 624 |
6004C3 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 648 |
6004CM | Not interchangeable | sealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 450 |
6004LB | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 764 |
6004LLB | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 604 |
6004LLB/LP03 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 768 |
6004LLBC3 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 792 |
6004LLBC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 876 |
6004LLBCM | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 701 |
6004LLBCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 603 |
6004LLBNR | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 716 |
6004LLBNR/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 715 |
6004LLU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 665 |
6004LLUC3 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 631 |
6004LLUC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 835 |
6004LLUCM | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 784 |
6004LLUCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 550 |
6004LLUNR | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 688 |
6004LLUNR/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 672 |
6004LU | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 581 |
6004NR | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 817 |
6004P4 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1910 |
6004P5 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1296 |
6004Z | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 533 |
6004ZC3 | Close, not equivalent | clearance: CM vs C3 | JPY 532 |
6004ZNR | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 930 |
6004ZZ | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 487 |
6004ZZ/LP03 | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 608 |
6004ZZC3 | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 767 |
6004ZZC3/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 821 |
6004ZZC4/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 870 |
6004ZZCM | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 424 |
6004ZZCM/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 534 |
6004ZZNR | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 581 |
6004ZZNR/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 586 |
6004ZZP5/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1500 |
All 36 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 409 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.