6010CM bearing (50 × 80 × 16 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6010CM as a deep groove ball bearing with 50 mm bore × 80 mm outside diameter × 16 mm width · open (no seal or shield) · basic dynamic load rating C = 21,800 N · list price JPY 1,484/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6010CM?

Boundary dimensions are 50 × 80 × 16 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)50
Outside diameter D (mm)80
Width B (mm)16
How is the part number 6010CM read?

The base number splits into series 60 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6010CM?

C = 21,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)21800
Load directionradial
Rowssingle row
Is 6010CM sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 50 × 80 × 16 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6010CM?

8,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)8400
Which bearings can replace 6010CM among the 50 × 80 × 16 mm parts?

31 listings share the 50 × 80 × 16 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6010CM specifically: 0 exact equivalent, 2 close but not equivalent, 28 not interchangeable, 0 not assessable.

Part numbervs 6010CMWhat differsList price
6010Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1453
6010C3Close, not equivalentclearance: CM vs C3JPY 1298
6010LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1992
6010LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1898
6010LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2613
6010LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1538
6010LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1876
6010LLBNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1920
6010LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1671
6010LLU/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2100
6010LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1604
6010LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1656
6010LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1595
6010LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1822
6010LLUNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1920
6010LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1740
6010P5Not interchangeableclearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 5714
6010ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1729
6010ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2654
6010ZNRNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1790
6010ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1861
6010ZZ/LP03Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1920
6010ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1458
6010ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2175
6010ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1610
6010ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1546
6010ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2199
6010ZZNR/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1736
6010ZZP5Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 3998
6010ZZP5/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 5370

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6010CM cost?

JPY 1,484 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6010CM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6010CM. The listing is tools.agentkit.ltd/s/BT-6010CM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,484 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.