Boundary dimensions are 50 × 80 × 16 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 50 |
| Outside diameter D (mm) | 80 |
| Width B (mm) | 16 |
The base number splits into series 60 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 21,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 21800 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 50 × 80 × 16 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 50 × 80 × 16 mm; only sealing (and therefore drag and top speed) changes.
8,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 8400 |
31 listings share the 50 × 80 × 16 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6010ZZP5/2AS specifically: 1 exact equivalent, 0 close but not equivalent, 29 not interchangeable, 0 not assessable.
| Part number | vs 6010ZZP5/2AS | What differs | List price |
|---|---|---|---|
6010 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1453 |
6010C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1298 |
6010CM | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1484 |
6010LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1992 |
6010LLBC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1898 |
6010LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2613 |
6010LLBCM | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1538 |
6010LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1876 |
6010LLBNR/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the other | JPY 1920 |
6010LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1671 |
6010LLU/LP03 | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2100 |
6010LLUC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1604 |
6010LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1656 |
6010LLUCM | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1595 |
6010LLUCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1822 |
6010LLUNR/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the other | JPY 1920 |
6010LU | Not interchangeable | sealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1740 |
6010P5 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5714 |
6010Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1729 |
6010ZCM | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2654 |
6010ZNR | Not interchangeable | sealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the other | JPY 1790 |
6010ZZ | Not interchangeable | precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1861 |
6010ZZ/LP03 | Not interchangeable | precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1920 |
6010ZZC3 | Not interchangeable | clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1458 |
6010ZZC3/5K | Not interchangeable | clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2175 |
6010ZZC4/5K | Not interchangeable | clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1610 |
6010ZZCM/5K | Not interchangeable | clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1546 |
6010ZZNR | Not interchangeable | precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the other | JPY 2199 |
6010ZZNR/2AS | Not interchangeable | precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the other | JPY 1736 |
6010ZZP5 | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 3998 |
All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 5,370 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.