Boundary dimensions are 15 × 35 × 11 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 15 |
| Outside diameter D (mm) | 35 |
| Width B (mm) | 11 |
The base number splits into series 62 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 7,750 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 7750 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 15 × 35 × 11 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 15 × 35 × 11 mm; only sealing (and therefore drag and top speed) changes.
15,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 15000 |
38 listings share the 15 × 35 × 11 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6202LLU/LP03 specifically: 4 exact equivalent, 12 close but not equivalent, 21 not interchangeable, 0 not assessable.
| Part number | vs 6202LLU/LP03 | What differs | List price |
|---|---|---|---|
6202C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 534 |
6202CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 358 |
6202JR2C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 457 |
6202LB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 681 |
6202LLB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 527 |
6202LLBC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 681 |
6202LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 692 |
6202LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 656 |
6202LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 469 |
6202LLBNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 890 |
6202LLU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 527 |
6202LLUC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 477 |
6202LLUC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 623 |
6202LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 664 |
6202LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 456 |
6202LLUNR | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 658 |
6202LU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 656 |
6202NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 820 |
6202P4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1389 |
6202Z | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 633 |
6202ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 820 |
6202ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 615 |
6202ZNR | Not interchangeable | sealing: rubber seal vs shielded, one side; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 729 |
6202ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 635 |
6202ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 681 |
6202ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 631 |
6202ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 633 |
6202ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 488 |
6202ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 409 |
6202ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 424 |
6202ZZCM/L448 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 516 |
6202ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 541 |
6202ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 705 |
6202ZZP5 | Not interchangeable | sealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1007 |
6202ZZP5/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1160 |
EC-6202LLBC3/2AS | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 639 |
EC-6202LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 960 |
All 37 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 940 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.