6202P4 bearing (15 × 35 × 11 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6202P4 as a deep groove ball bearing with 15 mm bore × 35 mm outside diameter × 11 mm width · open (no seal or shield) · basic dynamic load rating C = 7,750 N · list price JPY 1,389/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6202P4?

Boundary dimensions are 15 × 35 × 11 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)15
Outside diameter D (mm)35
Width B (mm)11
How is the part number 6202P4 read?

The base number splits into series 62 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6202P4?

C = 7,750 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)7750
Load directionradial
Rowssingle row
Is 6202P4 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 15 × 35 × 11 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6202P4?

19,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)19000
Which bearings can replace 6202P4 among the 15 × 35 × 11 mm parts?

38 listings share the 15 × 35 × 11 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6202P4 specifically: 0 exact equivalent, 0 close but not equivalent, 37 not interchangeable, 0 not assessable.

Part numbervs 6202P4What differsList price
6202C3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 534
6202CMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 358
6202JR2C3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 457
6202LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 681
6202LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 527
6202LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 681
6202LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 692
6202LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 656
6202LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 469
6202LLBNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 890
6202LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 527
6202LLU/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6202LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 477
6202LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 623
6202LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 664
6202LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 456
6202LLUNRNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 658
6202LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 656
6202NRNot interchangeableprecision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 820
6202ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 633
6202ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 820
6202ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 615
6202ZNRNot interchangeablesealing: open (no seal or shield) vs shielded, one side; precision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 729
6202ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 635
6202ZZ/LP03Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 681
6202ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 631
6202ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 633
6202ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 488
6202ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 409
6202ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 424
6202ZZCM/L448Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 516
6202ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 541
6202ZZNR/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 705
6202ZZP5Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1007
6202ZZP5/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 4 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1160
EC-6202LLBC3/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 639
EC-6202LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 4 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 960

All 37 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6202P4 cost?

JPY 1,389 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6202P4?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6202P4. The listing is tools.agentkit.ltd/s/BT-6202P4. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,389 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.