Boundary dimensions are 35 × 72 × 17 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 35 |
| Outside diameter D (mm) | 72 |
| Width B (mm) | 17 |
The base number splits into series 62 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 25,700 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 25700 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 35 × 72 × 17 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 35 × 72 × 17 mm; only sealing (and therefore drag and top speed) changes.
9,800 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 9800 |
38 listings share the 35 × 72 × 17 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6207LLBC3/5K specifically: 4 exact equivalent, 11 close but not equivalent, 22 not interchangeable, 0 not assessable.
| Part number | vs 6207LLBC3/5K | What differs | List price |
|---|---|---|---|
6207 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1004 |
6207C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1017 |
6207C4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 883 |
6207CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 868 |
6207L1C3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1440 |
6207LB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1152 |
6207LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1347 |
6207LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1205 |
6207LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 1068 |
6207LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 1291 |
6207LLBNR/2AS | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 1440 |
6207LLBP5/2AS | Not interchangeable | clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2670 |
6207LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1334 |
6207LLU/LP03 | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1560 |
6207LLUC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1317 |
6207LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1249 |
6207LLUC4/5K | Close, not equivalent | clearance: C3 vs C4 | JPY 1330 |
6207LLUCM | Close, not equivalent | clearance: C3 vs CM | JPY 1215 |
6207LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 1194 |
6207LU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1481 |
6207NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1121 |
6207NRC3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2031 |
6207P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 3046 |
6207Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1116 |
6207ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1169 |
6207ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1029 |
6207ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1440 |
6207ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1221 |
6207ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1145 |
6207ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1240 |
6207ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1145 |
6207ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1419 |
6207ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1123 |
6207ZZNRC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 995 |
6207ZZNRC3/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1108 |
6207ZZP5 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2796 |
6207ZZP5/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2590 |
All 37 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,217 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.