Boundary dimensions are 60 × 110 × 22 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 60 |
| Outside diameter D (mm) | 110 |
| Width B (mm) | 22 |
The base number splits into series 62 and bore code 12. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 12 therefore means a 60 mm bore, which matches the 60 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 52,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 52500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 60 × 110 × 22 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 60 × 110 × 22 mm; only sealing (and therefore drag and top speed) changes.
6,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 6000 |
31 listings share the 60 × 110 × 22 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6212LLB specifically: 4 exact equivalent, 9 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6212LLB | What differs | List price |
|---|---|---|---|
6212 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2406 |
6212C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1965 |
6212CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1953 |
6212L1 | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 4210 |
6212LB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2632 |
6212LLBC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2412 |
6212LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 3948 |
6212LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2893 |
6212LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2817 |
6212LLBNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 2730 |
6212LLU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2598 |
6212LLUC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2440 |
6212LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2516 |
6212LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2683 |
6212LLUNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 2730 |
6212LU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2440 |
6212NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2290 |
6212Z | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2967 |
6212ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2230 |
6212ZC4 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2230 |
6212ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2330 |
6212ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2680 |
6212ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2885 |
6212ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2656 |
6212ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2230 |
6212ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2517 |
6212ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2667 |
6212ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2732 |
6212ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2732 |
6212ZZP5/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 7230 |
All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,951 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.