6212LLBCM bearing (60 × 110 × 22 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6212LLBCM as a deep groove ball bearing with 60 mm bore × 110 mm outside diameter × 22 mm width · rubber seal · basic dynamic load rating C = 52,500 N · list price JPY 2,893/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6212LLBCM?

Boundary dimensions are 60 × 110 × 22 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)60
Outside diameter D (mm)110
Width B (mm)22
How is the part number 6212LLBCM read?

The base number splits into series 62 and bore code 12. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 12 therefore means a 60 mm bore, which matches the 60 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6212LLBCM?

C = 52,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)52500
Load directionradial
Rowssingle row
Is 6212LLBCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 60 × 110 × 22 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6212LLBCM?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 60 × 110 × 22 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6212LLBCM?

6,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)6000
Which bearings can replace 6212LLBCM among the 60 × 110 × 22 mm parts?

31 listings share the 60 × 110 × 22 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6212LLBCM specifically: 3 exact equivalent, 10 close but not equivalent, 17 not interchangeable, 0 not assessable.

Part numbervs 6212LLBCMWhat differsList price
6212Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2406
6212C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1965
6212CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1953
6212L1Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 4210
6212LBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 2632
6212LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 2951
6212LLBC3Close, not equivalentclearance: CM vs C3JPY 2412
6212LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 3948
6212LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2817
6212LLBNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 2730
6212LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 2598
6212LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 2440
6212LLUCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2516
6212LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2683
6212LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 2730
6212LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 2440
6212NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2290
6212ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2967
6212ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2230
6212ZC4Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2230
6212ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2330
6212ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2680
6212ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2885
6212ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2656
6212ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2230
6212ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2517
6212ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2667
6212ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2732
6212ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2732
6212ZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 7230

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6212LLBCM cost?

JPY 2,893 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6212LLBCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6212LLBCM. The listing is tools.agentkit.ltd/s/BT-6212LLBCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 2,893 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.