Boundary dimensions are 80 × 140 × 26 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 80 |
| Outside diameter D (mm) | 140 |
| Width B (mm) | 26 |
The base number splits into series 62 and bore code 16. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 16 therefore means a 80 mm bore, which matches the 80 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 72,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 72500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 80 × 140 × 26 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 80 × 140 × 26 mm; only sealing (and therefore drag and top speed) changes.
4,500 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 4500 |
25 listings share the 80 × 140 × 26 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6216LLBC3/5K specifically: 4 exact equivalent, 6 close but not equivalent, 14 not interchangeable, 0 not assessable.
| Part number | vs 6216LLBC3/5K | What differs | List price |
|---|---|---|---|
6216 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3497 |
6216C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3705 |
6216C4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4930 |
6216CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3764 |
6216L1C3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 5980 |
6216LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 5237 |
6216LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 5885 |
6216LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 3948 |
6216LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 4215 |
6216LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 5556 |
6216LLUC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 4499 |
6216LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 5223 |
6216LLUCM | Close, not equivalent | clearance: C3 vs CM | JPY 4155 |
6216LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 4883 |
6216NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4518 |
6216NXR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5470 |
6216Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5330 |
6216ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4328 |
6216ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5366 |
6216ZNR | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5560 |
6216ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3898 |
6216ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4080 |
6216ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4328 |
6216ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4573 |
All 24 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 6,280 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.