6300ZU1 bearing (10 × 35 × 11 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6300ZU1 as a deep groove ball bearing with 10 mm bore × 35 mm outside diameter × 11 mm width · shielded, one side · basic dynamic load rating C = 8,200 N · list price JPY 860/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6300ZU1?

Boundary dimensions are 10 × 35 × 11 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)10
Outside diameter D (mm)35
Width B (mm)11
How is the part number 6300ZU1 read?

The base number splits into series 63 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6300ZU1?

C = 8,200 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)8200
Load directionradial
Rowssingle row
Is 6300ZU1 sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 10 × 35 × 11 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6300ZU1?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 10 × 35 × 11 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6300ZU1?

27,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)27000
Which bearings can replace 6300ZU1 among the 10 × 35 × 11 mm parts?

23 listings share the 10 × 35 × 11 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6300ZU1 specifically: 0 exact equivalent, 1 close but not equivalent, 21 not interchangeable, 0 not assessable.

Part numbervs 6300ZU1What differsList price
6300Not interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 576
6300C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 489
6300CMNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 470
6300LLBNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 768
6300LLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 752
6300LLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 774
6300LLBCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 498
6300LLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 665
6300LLUNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 728
6300LLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 727
6300LLUCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 638
6300LLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 630
6300LUNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 890
6300U1Not interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 522
6300ZC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 566
6300ZZNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 633
6300ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 664
6300ZZC3/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 650
6300ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 434
6300ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 649
6300ZZNRNot interchangeablesealing: shielded, one side vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 795
6300ZZNR/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 664

All 22 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6300ZU1 cost?

JPY 860 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6300ZU1?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6300ZU1. The listing is tools.agentkit.ltd/s/BT-6300ZU1. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 860 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.