6302LLUCM bearing (15 × 42 × 13 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6302LLUCM as a deep groove ball bearing with 15 mm bore × 42 mm outside diameter × 13 mm width · rubber seal · basic dynamic load rating C = 11,400 N · list price JPY 570/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6302LLUCM?

Boundary dimensions are 15 × 42 × 13 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)15
Outside diameter D (mm)42
Width B (mm)13
How is the part number 6302LLUCM read?

The base number splits into series 63 and bore code 02. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 02 therefore means a 15 mm bore, which matches the 15 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6302LLUCM?

C = 11,400 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)11400
Load directionradial
Rowssingle row
Is 6302LLUCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 15 × 42 × 13 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6302LLUCM?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 15 × 42 × 13 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6302LLUCM?

12,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)12000
Which bearings can replace 6302LLUCM among the 15 × 42 × 13 mm parts?

28 listings share the 15 × 42 × 13 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6302LLUCM specifically: 3 exact equivalent, 9 close but not equivalent, 15 not interchangeable, 0 not assessable.

Part numbervs 6302LLUCMWhat differsList price
6302Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 669
6302C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 656
6302CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 579
6302LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 638
6302LLB/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1030
6302LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 920
6302LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 699
6302LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 730
6302LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 776
6302LLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 747
6302LLUC3Close, not equivalentclearance: CM vs C3JPY 878
6302LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 590
6302LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 723
6302LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 970
6302LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 920
6302ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 706
6302ZNRNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 930
6302ZU1Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 679
6302ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 539
6302ZZ/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 696
6302ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 980
6302ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 734
6302ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 419
6302ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6302ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 686
6302ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 569
6302ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 649

All 27 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6302LLUCM cost?

JPY 570 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6302LLUCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6302LLUCM. The listing is tools.agentkit.ltd/s/BT-6302LLUCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 570 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.