6303C3 bearing (17 × 47 × 14 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6303C3 as a deep groove ball bearing with 17 mm bore × 47 mm outside diameter × 14 mm width · open (no seal or shield) · basic dynamic load rating C = 13,500 N · list price JPY 722/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6303C3?

Boundary dimensions are 17 × 47 × 14 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)17
Outside diameter D (mm)47
Width B (mm)14
How is the part number 6303C3 read?

The base number splits into series 63 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6303C3?

C = 13,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)13500
Load directionradial
Rowssingle row
Is 6303C3 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 17 × 47 × 14 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6303C3?

16,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)16000
Which bearings can replace 6303C3 among the 17 × 47 × 14 mm parts?

29 listings share the 17 × 47 × 14 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6303C3 specifically: 0 exact equivalent, 3 close but not equivalent, 25 not interchangeable, 0 not assessable.

Part numbervs 6303C3What differsList price
6303Close, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 724
6303CMClose, not equivalentclearance: C3 vs CMJPY 491
6303LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 751
6303LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 897
6303LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 937
6303LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 920
6303LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 855
6303LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 606
6303LLBNRNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 863
6303LLBP5/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1760
6303LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 732
6303LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1000
6303LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 844
6303LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 803
6303LUZC4/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1050
6303NRClose, not equivalentclearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 713
6303ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 805
6303ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 826
6303ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 696
6303ZNRNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1010
6303ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 648
6303ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 780
6303ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 770
6303ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 950
6303ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 585
6303ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 776
6303ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 766
6303ZZNR/2ANot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1074

All 28 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6303C3 cost?

JPY 722 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6303C3?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6303C3. The listing is tools.agentkit.ltd/s/BT-6303C3. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 722 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.