Boundary dimensions are 17 × 47 × 14 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 17 |
| Outside diameter D (mm) | 47 |
| Width B (mm) | 14 |
The base number splits into series 63 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 13,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 13500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 17 × 47 × 14 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 17 × 47 × 14 mm; only sealing (and therefore drag and top speed) changes.
16,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 16000 |
29 listings share the 17 × 47 × 14 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6303LLBC3/5K specifically: 2 exact equivalent, 9 close but not equivalent, 17 not interchangeable, 0 not assessable.
| Part number | vs 6303LLBC3/5K | What differs | List price |
|---|---|---|---|
6303 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 724 |
6303C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 722 |
6303CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 491 |
6303LB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 751 |
6303LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 897 |
6303LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 937 |
6303LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 855 |
6303LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 606 |
6303LLBNR | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 863 |
6303LLBP5/2AS | Not interchangeable | clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1760 |
6303LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 732 |
6303LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1000 |
6303LLUCM | Close, not equivalent | clearance: C3 vs CM | JPY 844 |
6303LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 803 |
6303LUZC4/2AS | Close, not equivalent | clearance: C3 vs C4 | JPY 1050 |
6303NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 713 |
6303Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 805 |
6303ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 826 |
6303ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 696 |
6303ZNR | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1010 |
6303ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 648 |
6303ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 780 |
6303ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 770 |
6303ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 950 |
6303ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 585 |
6303ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 776 |
6303ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 766 |
6303ZZNR/2A | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1074 |
All 28 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 920 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.