6308C4 bearing (40 × 90 × 23 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6308C4 as a deep groove ball bearing with 40 mm bore × 90 mm outside diameter × 23 mm width · open (no seal or shield) · basic dynamic load rating C = 40,500 N · list price JPY 1,862/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6308C4?

Boundary dimensions are 40 × 90 × 23 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)40
Outside diameter D (mm)90
Width B (mm)23
How is the part number 6308C4 read?

The base number splits into series 63 and bore code 08. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 08 therefore means a 40 mm bore, which matches the 40 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6308C4?

C = 40,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)40500
Load directionradial
Rowssingle row
Is 6308C4 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 40 × 90 × 23 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6308C4?

7,800 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)7800
Which bearings can replace 6308C4 among the 40 × 90 × 23 mm parts?

37 listings share the 40 × 90 × 23 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6308C4 specifically: 0 exact equivalent, 5 close but not equivalent, 31 not interchangeable, 0 not assessable.

Part numbervs 6308C4What differsList price
6308Close, not equivalentclearance: C4 vs not stated (standard group assumed)JPY 2101
6308C3Close, not equivalentclearance: C4 vs C3JPY 2354
6308CMClose, not equivalentclearance: C4 vs CMJPY 1860
6308L1C3Close, not equivalentclearance: C4 vs C3JPY 2440
6308LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2190
6308LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2813
6308LLB/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2227
6308LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2944
6308LLBC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2826
6308LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3023
6308LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2760
6308LLBP5/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 6337
6308LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2510
6308LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2620
6308LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2371
6308LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2103
6308LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2450
6308LLUNR/2ASNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2440
6308LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2190
6308M8C3P6Not interchangeableclearance: C4 vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the otherJPY 4500
6308NRClose, not equivalentclearance: C4 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 2060
6308ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2856
6308ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2455
6308ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2754
6308ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2602
6308ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2491
6308ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2467
6308ZZC3/L448Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2440
6308ZZC4Not interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1653
6308ZZC4/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2067
6308ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2231
6308ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2430
6308ZZD2C3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5410
6308ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2812
6308ZZNR/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2376
6308ZZP5/2ASNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: C4 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 6580

All 36 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6308C4 cost?

JPY 1,862 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6308C4?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6308C4. The listing is tools.agentkit.ltd/s/BT-6308C4. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,862 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.