Boundary dimensions are 40 × 90 × 23 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 40 |
| Outside diameter D (mm) | 90 |
| Width B (mm) | 23 |
The base number splits into series 63 and bore code 08. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 08 therefore means a 40 mm bore, which matches the 40 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 40,500 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 40500 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 40 × 90 × 23 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 40 × 90 × 23 mm; only sealing (and therefore drag and top speed) changes.
7,800 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 7800 |
37 listings share the 40 × 90 × 23 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6308LLB/5K specifically: 4 exact equivalent, 9 close but not equivalent, 23 not interchangeable, 0 not assessable.
| Part number | vs 6308LLB/5K | What differs | List price |
|---|---|---|---|
6308 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2101 |
6308C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2354 |
6308C4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1862 |
6308CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1860 |
6308L1C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2440 |
6308LB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2190 |
6308LLB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2813 |
6308LLBC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2944 |
6308LLBC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2826 |
6308LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 3023 |
6308LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2760 |
6308LLBP5/2AS | Not interchangeable | precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 6337 |
6308LLU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2510 |
6308LLUC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2620 |
6308LLUC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 2371 |
6308LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2103 |
6308LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 2450 |
6308LLUNR/2AS | Close, not equivalent | outer ring: flat vs with snap-ring groove (U-groove) | JPY 2440 |
6308LU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 2190 |
6308M8C3P6 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the other | JPY 4500 |
6308NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2060 |
6308Z | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2856 |
6308ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2455 |
6308ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2754 |
6308ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2602 |
6308ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2491 |
6308ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2467 |
6308ZZC3/L448 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2440 |
6308ZZC4 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1653 |
6308ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2067 |
6308ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2231 |
6308ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2430 |
6308ZZD2C3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5410 |
6308ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2812 |
6308ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2376 |
6308ZZP5/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 6580 |
All 36 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 2,227 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.