6310LLUCM bearing (50 × 110 × 27 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6310LLUCM as a deep groove ball bearing with 50 mm bore × 110 mm outside diameter × 27 mm width · rubber seal · basic dynamic load rating C = 62,000 N · list price JPY 3,305/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6310LLUCM?

Boundary dimensions are 50 × 110 × 27 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)50
Outside diameter D (mm)110
Width B (mm)27
How is the part number 6310LLUCM read?

The base number splits into series 63 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6310LLUCM?

C = 62,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)62000
Load directionradial
Rowssingle row
Is 6310LLUCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 50 × 110 × 27 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6310LLUCM?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 50 × 110 × 27 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6310LLUCM?

4,200 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)4200
Which bearings can replace 6310LLUCM among the 50 × 110 × 27 mm parts?

33 listings share the 50 × 110 × 27 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6310LLUCM specifically: 3 exact equivalent, 9 close but not equivalent, 20 not interchangeable, 0 not assessable.

Part numbervs 6310LLUCMWhat differsList price
6310Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3299
6310C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3521
6310C4Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2664
6310CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3151
6310LBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 4710
6310LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 4046
6310LLBC3Close, not equivalentclearance: CM vs C3JPY 4661
6310LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 3987
6310LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2772
6310LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 3462
6310LLBNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 5090
6310LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 3339
6310LLUC3Close, not equivalentclearance: CM vs C3JPY 3527
6310LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 3340
6310LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 3484
6310LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 3111
6310M8C3P6Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the otherJPY 5360
6310NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2832
6310NRC3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4593
6310ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3518
6310ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4430
6310ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3065
6310ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3682
6310ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3084
6310ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3221
6310ZZC4Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2478
6310ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2615
6310ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3504
6310ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3237
6310ZZCM/L448Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 4430
6310ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3798
6310ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 3468

All 32 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6310LLUCM cost?

JPY 3,305 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6310LLUCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6310LLUCM. The listing is tools.agentkit.ltd/s/BT-6310LLUCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 3,305 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.